Fully charge the device before first use for optimal performance as the battery comes with only a minimal charge for safe delivery.

Full charging will take over 3-4 hours.

It is set for use once fully charged.

🔋The JollyRide™ Blow-Vac charges via a USB Type-A to Type-C cable.

1. Plug the USB Type-C end into the device.

2. Connect the USB Type-A end to a standard USB Type-A charger with 5V⎓1A or 5V⎓2.1A output for best charging result.

3. Charging indicator:
• 🔴 Red light = Charging
• 🟢 Green light = Fully charged

Turning ON:

• Press and hold the power button for "3 seconds" to turn on the device. It will start at Low (🟢 Green) – ideal for general vacuuming.

• Press the button again to switch to Med (🟡Yellow) – suitable for more demanding tasks.

• Press the button once more to activate Max (🔴Red) – the highest power level for maximum performance.


Turning OFF:

• Press and hold the power button for "3 seconds" at any strength level to turn off the device.


Note:
• Do not keep pressing the button after the power is on, as this will turn the device off.
• If use as a vacuum, ensure the HEPA Filter is installed in the Vac-cup before use so to protect the engine from tiny dust and debris. 

JollyRide™ Blow-Vac 4-in-1 features 3 Power Modes to fit your cleaning needs:

🟢 Low (30 min) — Handles sand, crumbs, pet hair, and even $2 coins. Ideal for everyday cleaning. 30-minute run time ranks among the longest in mini vacs.

🟡 Med (20 min) — Adds an extra boost when you need more suction.

🔴 Max (10 min) — Best for blow function, same battery runtime as V15 on its Max mode.

For Vacuum and Deflate:
Attach the accessories to the side with a black suction hole. (Same side of the power button)

For Blow and Inflate:
Attach the accessories to the side with golden rings (the opposite side of the power button)

🪥 Basic Clean (**After each vacuum for the continuous best performance)

1. Remove the Vac Cup from the main unit. 

2. Carefully take out the HEPA filter from the Vac Cup (Note: The filter may be saturated with fine dust and debris so avoid doing so in windy condition).

3. Empty larger debris from the Vac Cup into the bin. 

4. Use an old toothbrush to gently brush off any remaining dust and debris from the HEPA filter into the bin.
(Outdoors, you can use the blow function to clean the dust off the filter, but it's not recommended indoors.)

5. Reassemble the HEPA filter into the Vac Cup, then attach the Vac Cup back to the main unit for the next use. 

🧼 Deep Clean (Occasionally) 

1. Follow the Basic Clean steps through step 4. 

2. Wash the Vac Cup and HEPA under running water for a thorough clean. (If cleaning is difficult, use warm water and a small amount of detergent to assist.)

3. Shake off excess water or use a towel to absorb any remaining moisture. 

4. Allow all parts to air dry completely. (** Do not use until it fully dry, as moisture can damage the engine.) 

5. Once dry, reassemble for the next use.

⚠️Before vacuuming, make sure the HEPA Filter is installed inside the Vac-Cup.

This is crucial for effective filtration, trapping dust and allergens, and maintaining optimal suction power.

Without the filter, debris can escape back into the air, compromising your cleaning efficiency and indoor air quality.

Additionally, this can lead to debris and dirt being sucked into the motor, potentially causing internal damage of the motor.

⚠️ Do not use the Vac cup and Blow nozzle at the same time.

For optimal performance and to prevent overheating, we suggest using each function separately to achieve the best results and protect the motor.


⚠️Make sure the filter and the Vac-cup are fully dried after washing for next use.

⚠️Avoid direct sun light on the device, especially when charging and store in the car.